GuiSession

stationCode
ReaderFT_01
scandData
000006318,AS000016REVC054424
ATPName
Reader2.0_FullATP_20241112_113709
startTime
11/13/2024 15:32:09
endTime
11/13/2024 15:38:12
Duration
06:03.287
Status
Error

Test Results

index TestName Min Limit ResultAnswer Max Limit ResultStatus Duration
0 Initialize Pass 00:00.000
1 init Pass Pass 00:03.811
2 PoE : OC Pass 00:00.000
3 PoE : OC : Open circuit test :Turn on the 54V Pass Pass 00:00.197
4 PoE : OC : Set NXP RST Pass Pass 00:00.036
5 Delay 1000ms Pass Pass 00:01.000
6 PoE : OC : Read PoE+ voltage rail (PoE_P_ADC) (mv) 0 Pass 00:00.151
7 PoE : OC : PoE VDD voltage rail (PoE_VDD_ADC) (mv) 1 Pass 00:00.155
8 PoE : OC : PoE VDD voltage rail (PoE_VT15_ADC) (mv) 0 Pass 00:00.166
9 PoE : OC : Measure the current over 54V rail (Vbus54V) (mA) 32 Pass 00:00.031
10 PoE : OC : Read 4.6V rail voltage (ADC_4V6_Load) (mv) 4450 4537 4650 Pass 00:00.032
11 PoE : CC Pass 00:00.000
12 PoE : CC : turn on Load 4.6V rail with external resistor (Load4V6) Pass Pass 00:00.029
13 Delay 100ms Pass Pass 00:00.100
14 PoE : CC : Read PoE+ voltage rail (PoE_P_ADC) (mv) Skip Pass 00:00.000
15 PoE : CC : PoE VDD voltage rail (PoE_VDD_ADC) (mv) Skip Pass 00:00.000
16 PoE : CC : PoE VDD voltage rail (PoE_VT15_ADC) (mv) Skip Pass 00:00.000
17 PoE : CC : Measure the current over 54V rail (Vbus54V) (mA) 233 Pass 00:00.029
18 PoE : CC : Read 4.6V rail voltage (ADC_4V6_Load) (mv) 4300 Pass 00:00.039
19 PoE : CC : turn off Load 4.6V rail with external resistor (Load4V6) Pass Pass 00:00.025
20 PoE : CC : Open circuit test :Turn Off the 54V Pass Pass 00:00.037
21 PA 4.6V : OC Pass 00:00.000
22 PA 4.6V : OC : Turn on the 4.6V high current source (Vbus4V6H) Pass Pass 00:00.038
23 Delay 500ms Pass Pass 00:00.500
24 PA 4.6V : OC : Read 4.6V PA voltage rail 4100 4267 4600 Pass 00:00.031
25 PA 4.6V : OC : Measure the current over 4.6V high current rail 50 201 600 Pass 00:00.032
26 PA 4.6V : CC : Pass 00:00.000
27 PA 4.6V : CC : Load 4.6V PA rail with external resistor Skip Pass 00:00.000
28 Delay 100ms Skip Pass 00:00.000
29 PA 4.6V : CC : Read 4.6V PA voltage rail 2400 Skip 2800 Pass 00:00.000
30 PA 4.6V : CC : Measure the current over 4.6V high current rail 1000 Skip 2000 Pass 00:00.000
31 PA 4.6V : CC : Turn off the external load for 4.6V PA rail Skip Pass 00:00.000
32 MCU LDO : OC Pass 00:00.000
33 MCU LDO : OC : Release NXP RST Pass Pass 00:00.032
34 Delay 500ms Pass Pass 00:00.500
35 MCU LDO : OC : Read 3.5V voltage rail (ADC_3V5_MCU) - (mV) 3300 3543 3600 Pass 00:00.028
36 MCU LDO : OC : Measure the current over 4.6V high current rail (Vbus4V6H) (mA) 15 315 1000 Pass 00:00.031
37 BLE LDO : OC Pass 00:00.000
38 BLE LDO : OC : Release RST of 3.3V BLE LDO (LDO_BLE) Pass Pass 00:00.037
39 Delay 500ms Pass Pass 00:00.500
40 BLE LDO : OC : Read 3.3V BLE voltage rail (ADC_3V3_BLE) - (mV) 3250 3314 3350 Pass 00:00.038
41 BLE LDO : OC : Measure the current over 4.6V high current rail (Vbus4V6H) - (mA) 50 329 1000 Pass 00:00.036
42 LNA LDO : OC Pass 00:00.000
43 LNA LDO : OC : Release RST of 3.3V BLE LDO (LDO_LNA) Pass Pass 00:00.035
44 Delay 100ms Pass Pass 00:00.100
45 LNA LDO : OC : Read 3.3V BLE voltage rail (ADC_3V3_LNA) - (mV) 3250 3319 3350 Pass 00:00.035
46 LNA LDO : OC : Measure the current over 4.6V high current rail (Vbus4V6H) - (mA) 60 543 1000 Pass 00:00.025
47 Flashing NXP Pass 00:00.000
48 TesterMCU_BoardReset Pass Pass 00:00.025
49 Turn on the 4.6V high current source (Vbus4V6H) Pass Pass 00:00.029
50 Set SWD splitter to Out1 Pass Pass 00:00.026
51 Release NXP reset line Pass Pass 00:00.036
52 Jflash_Programming jlink2 workaround Pass Pass 00:02.008
53 Jflash_Programming jlink2 nxp boot Pass Pass 00:01.713
54 Jflash_Programming jlink2 nxp application Pass Pass 00:09.904
55 Set NXP reset line Pass Pass 00:00.034
56 Delay 500 Pass Pass 00:00.500
57 Release NXP reset line Pass Pass 00:00.037
58 Delay 500 Pass Pass 00:00.500
59 Flashing ISM Pass 00:00.000
60 Release all pinout Pass Pass 00:00.033
61 Delay 4000 Pass Pass 00:04.000
62 Set SWD splitter to Out2 Pass Pass 00:00.025
63 Jflash_Programming jlink2 TX boot Pass Pass 00:00.487
64 Jflash_Programming jlink2 TX application Pass Pass 00:00.925
65 Flashing BLE 1 Pass 00:00.000
66 Set SWD splitter to Out1 Pass Pass 00:00.036
67 Release RST of 3.3V BLE LDO (LDO_BLE) Pass Pass 00:00.026
68 Jflash_Programming jlink1 ble Pass Pass 00:01.249
69 Flashing BLE 2 Pass 00:00.000
70 Set SWD splitter to Out2 Pass Pass 00:00.034
71 Jflash_Programming jlink1 ble Pass Pass 00:01.243
72 Flashing BLE 3 Pass 00:00.000
73 Set SWD splitter to Out3 Pass Pass 00:00.030
74 Jflash_Programming jlink1 ble Pass Pass 00:01.249
75 Reader PWR reset Pass 00:00.000
76 Turn OFF the 4.6V high current source (Vbus4V6H) Pass Pass 00:00.022
77 Release NXP reset line Pass Pass 00:00.032
78 Release all pinout Pass Pass 00:00.029
79 Turn ON the 4.6V high current source (Vbus4V6H) Pass Pass 00:00.030
80 Delay 6000 Pass Pass 00:06.000
81 Reader Connect Pass 00:00.000
82 ConnectToReaderTelnet 192.168.0.150 Pass 00:00.317
83 ReaderSetSerialNumber 000006318 Pass 00:00.469
84 ReaderSetMacAddress 1063A39001B0 Pass 00:00.368
85 Restart Reader Pass Pass 00:00.105
86 Delay 6000 Pass Pass 00:06.000
87 ReConnectToReaderTelnet 192.168.0.150 Pass 00:00.307
88 ReaderGetMacAddress 1063A39001B0 Pass 00:00.212
89 SendReaderConfigFile Pass Pass 00:09.355
90 Get Main CPU version 2.1.1+1029 Pass 00:00.110
91 Get TX CPU version 0.15 Pass 00:00.718
92 Get BLE0 CPU version 0.10 Pass 00:00.721
93 Get BLE1 CPU version 0.10 Pass 00:00.106
94 Get BLE2 CPU version 0.10 Pass 00:00.102
95 Start TX (warming up) Pass 00:00.000
96 TesterMCU_Set_ISM_Mux Pass Pass 00:00.026
97 Set TX on pwr = 240 freq = 902000 debug Pass Pass 00:01.682
98 Delay 10000 Pass Pass 00:10.000
99 BLE RX CH 37 Pass 00:00.000
100 ReaderBLE_PreTestConfig Pass Pass 00:07.445
101 ReaderBLEtest ch 37 -41.96 Pass 00:08.075
102 ReaderBLEtest ch 37 ant 1 -50 -42.00 100 Pass 00:08.065
103 ReaderBLEtest ch 37 ant 2 -50 -44.96 100 Pass 00:08.072
104 ReaderBLEtest ch 37 ant 3 -50 -44.29 100 Pass 00:08.087
105 ReaderBLEtest ch 37 ant 4 -50 -42.00 100 Pass 00:08.071
106 ReaderBLEtest ch 37 ant 5 -50 -51.18 100 Fail 00:08.073
107 ReaderBLEtest ch 37 ant 6 -50 -41.32 100 Pass 00:08.075
108 ReaderBLEtest ch 37 ant 7 -50 -42.00 100 Pass 00:08.065
109 BLE RX CH 38 Pass 00:00.000
110 ReaderBLE_PreTestConfig Pass Pass 00:07.429
111 ReaderBLEtest ch 38 -43.19 Pass 00:08.077
112 ReaderBLEtest ch 38 ant 1 -50 -43.49 100 Pass 00:08.076
113 ReaderBLEtest ch 38 ant 2 -50 -44.31 100 Pass 00:05.995
114 ReaderBLEtest ch 38 ant 3 -50 -43.56 100 Pass 00:08.071
115 ReaderBLEtest ch 38 ant 4 -50 -41.86 100 Pass 00:08.081
116 ReaderBLEtest ch 38 ant 5 -50 -53.00 100 Fail 00:05.994
117 ReaderBLEtest ch 38 ant 6 -50 -41.32 100 Pass 00:08.066
118 ReaderBLEtest ch 38 ant 7 -50 -42.00 100 Pass 00:08.070
119 BLE RX CH 39 Pass 00:00.000
120 ReaderBLE_PreTestConfig Pass Pass 00:07.432
121 ReaderBLEtest ch 39 -42.00 Pass 00:08.071
122 ReaderBLEtest ch 39 ant 1 -50 -42.00 100 Pass 00:08.070
123 ReaderBLEtest ch 39 ant 2 -50 -46.24 100 Pass 00:08.065
124 ReaderBLEtest ch 39 ant 3 -50 -43.77 100 Pass 00:08.072
125 ReaderBLEtest ch 39 ant 4 -50 -41.41 100 Pass 00:08.068
126 ReaderBLEtest ch 39 ant 5 -50 -58.68 100 Fail 00:05.994
127 ReaderBLEtest ch 39 ant 6 -50 -45.99 100 Pass 00:08.067
128 ReaderBLEtest ch 39 ant 7 -50 -44.10 100 Pass 00:08.083
129 ReaderBLE_PreTestConfig - stop scan Pass Pass 00:07.440
130 TX Test Pass 00:00.000
131 SetSpectrum Pass Pass 00:00.002
132 Get Last Spectrum Mesurment Freq 902000143.88 Pass 00:00.511
133 Get Last Spectrum Mesurment Amp 20 29.17 100 Pass 00:00.000
134 TX Calibration Pass 00:00.000
135 Reader Tx Warmup target 40 C - 45 C 38 Unable to write data to the transport connection: An existing connection was forcibly closed by the remote host.. 45 Error 01:10.613
136 ReaderCTune ( target freq - measure freq) (Hz) 0 400 Stop 00:00.000
Back to List