GuiSession

stationCode
ReaderFT_01
scandData
000005853,AS000016REVC054424
ATPName
Reader2.0_FullATP_20241112_113709
startTime
11/12/2024 13:05:33
endTime
11/12/2024 13:13:31
Duration
07:57.207
Status
Pass

Test Results

index TestName Min Limit ResultAnswer Max Limit ResultStatus Duration
0 Initialize Pass 00:00.000
1 init Pass Pass 00:03.688
2 PoE : OC Pass 00:00.000
3 PoE : OC : Open circuit test :Turn on the 54V Pass Pass 00:00.191
4 PoE : OC : Set NXP RST Pass Pass 00:00.034
5 Delay 1000ms Pass Pass 00:01.000
6 PoE : OC : Read PoE+ voltage rail (PoE_P_ADC) (mv) 0 Pass 00:00.148
7 PoE : OC : PoE VDD voltage rail (PoE_VDD_ADC) (mv) 1 Pass 00:00.153
8 PoE : OC : PoE VDD voltage rail (PoE_VT15_ADC) (mv) 0 Pass 00:00.146
9 PoE : OC : Measure the current over 54V rail (Vbus54V) (mA) 31 Pass 00:00.027
10 PoE : OC : Read 4.6V rail voltage (ADC_4V6_Load) (mv) 4450 4527 4650 Pass 00:00.028
11 PoE : CC Pass 00:00.000
12 PoE : CC : turn on Load 4.6V rail with external resistor (Load4V6) Pass Pass 00:00.026
13 Delay 100ms Pass Pass 00:00.100
14 PoE : CC : Read PoE+ voltage rail (PoE_P_ADC) (mv) Skip Pass 00:00.000
15 PoE : CC : PoE VDD voltage rail (PoE_VDD_ADC) (mv) Skip Pass 00:00.000
16 PoE : CC : PoE VDD voltage rail (PoE_VT15_ADC) (mv) Skip Pass 00:00.000
17 PoE : CC : Measure the current over 54V rail (Vbus54V) (mA) 230 Pass 00:00.025
18 PoE : CC : Read 4.6V rail voltage (ADC_4V6_Load) (mv) 4278 Pass 00:00.039
19 PoE : CC : turn off Load 4.6V rail with external resistor (Load4V6) Pass Pass 00:00.027
20 PoE : CC : Open circuit test :Turn Off the 54V Pass Pass 00:00.019
21 PA 4.6V : OC Pass 00:00.000
22 PA 4.6V : OC : Turn on the 4.6V high current source (Vbus4V6H) Pass Pass 00:00.015
23 Delay 500ms Pass Pass 00:00.500
24 PA 4.6V : OC : Read 4.6V PA voltage rail 4100 4262 4600 Pass 00:00.026
25 PA 4.6V : OC : Measure the current over 4.6V high current rail 50 201 600 Pass 00:00.106
26 PA 4.6V : CC : Pass 00:00.000
27 PA 4.6V : CC : Load 4.6V PA rail with external resistor Skip Pass 00:00.000
28 Delay 100ms Skip Pass 00:00.000
29 PA 4.6V : CC : Read 4.6V PA voltage rail 2400 Skip 2800 Pass 00:00.000
30 PA 4.6V : CC : Measure the current over 4.6V high current rail 1000 Skip 2000 Pass 00:00.000
31 PA 4.6V : CC : Turn off the external load for 4.6V PA rail Skip Pass 00:00.000
32 MCU LDO : OC Pass 00:00.000
33 MCU LDO : OC : Release NXP RST Pass Pass 00:00.034
34 Delay 500ms Pass Pass 00:00.500
35 MCU LDO : OC : Read 3.5V voltage rail (ADC_3V5_MCU) - (mV) 3300 3548 3600 Pass 00:00.025
36 MCU LDO : OC : Measure the current over 4.6V high current rail (Vbus4V6H) (mA) 15 296 1000 Pass 00:00.015
37 BLE LDO : OC Pass 00:00.000
38 BLE LDO : OC : Release RST of 3.3V BLE LDO (LDO_BLE) Pass Pass 00:00.027
39 Delay 500ms Pass Pass 00:00.500
40 BLE LDO : OC : Read 3.3V BLE voltage rail (ADC_3V3_BLE) - (mV) 3250 3308 3350 Pass 00:00.030
41 BLE LDO : OC : Measure the current over 4.6V high current rail (Vbus4V6H) - (mA) 50 243 1000 Pass 00:00.017
42 LNA LDO : OC Pass 00:00.000
43 LNA LDO : OC : Release RST of 3.3V BLE LDO (LDO_LNA) Pass Pass 00:00.016
44 Delay 100ms Pass Pass 00:00.100
45 LNA LDO : OC : Read 3.3V BLE voltage rail (ADC_3V3_LNA) - (mV) 3250 3312 3350 Pass 00:00.029
46 LNA LDO : OC : Measure the current over 4.6V high current rail (Vbus4V6H) - (mA) 60 243 1000 Pass 00:00.025
47 Flashing NXP Pass 00:00.000
48 TesterMCU_BoardReset Pass Pass 00:00.028
49 Turn on the 4.6V high current source (Vbus4V6H) Pass Pass 00:00.016
50 Set SWD splitter to Out1 Pass Pass 00:00.024
51 Release NXP reset line Pass Pass 00:00.018
52 Jflash_Programming jlink2 workaround Pass Pass 00:02.009
53 Jflash_Programming jlink2 nxp boot Pass Pass 00:01.753
54 Jflash_Programming jlink2 nxp application Pass Pass 00:09.897
55 Set NXP reset line Pass Pass 00:00.017
56 Delay 500 Pass Pass 00:00.500
57 Release NXP reset line Pass Pass 00:00.033
58 Delay 500 Pass Pass 00:00.500
59 Flashing ISM Pass 00:00.000
60 Release all pinout Pass Pass 00:00.021
61 Delay 4000 Pass Pass 00:04.000
62 Set SWD splitter to Out2 Pass Pass 00:00.036
63 Jflash_Programming jlink2 TX boot Pass Pass 00:00.554
64 Jflash_Programming jlink2 TX application Pass Pass 00:00.974
65 Flashing BLE 1 Pass 00:00.000
66 Set SWD splitter to Out1 Pass Pass 00:00.029
67 Release RST of 3.3V BLE LDO (LDO_BLE) Pass Pass 00:00.016
68 Jflash_Programming jlink1 ble Pass Pass 00:01.293
69 Flashing BLE 2 Pass 00:00.000
70 Set SWD splitter to Out2 Pass Pass 00:00.030
71 Jflash_Programming jlink1 ble Pass Pass 00:01.234
72 Flashing BLE 3 Pass 00:00.000
73 Set SWD splitter to Out3 Pass Pass 00:00.017
74 Jflash_Programming jlink1 ble Pass Pass 00:01.238
75 Reader PWR reset Pass 00:00.000
76 Turn OFF the 4.6V high current source (Vbus4V6H) Pass Pass 00:00.021
77 Release NXP reset line Pass Pass 00:00.017
78 Release all pinout Pass Pass 00:00.019
79 Turn ON the 4.6V high current source (Vbus4V6H) Pass Pass 00:00.017
80 Delay 6000 Pass Pass 00:06.000
81 Reader Connect Pass 00:00.000
82 ConnectToReaderTelnet 192.168.0.166 Pass 00:00.615
83 ReaderSetSerialNumber 000005853 Pass 00:00.321
84 ReaderSetMacAddress 1063A39002BD Pass 00:00.219
85 Restart Reader Pass Pass 00:00.106
86 Delay 6000 Pass Pass 00:06.000
87 ReConnectToReaderTelnet 192.168.0.166 Pass 00:00.328
88 ReaderGetMacAddress 1063A39002BD Pass 00:00.226
89 SendReaderConfigFile Pass Pass 00:09.581
90 Get Main CPU version 2.1.1+1029 Pass 00:00.108
91 Get TX CPU version 0.15 Pass 00:00.103
92 Get BLE0 CPU version 0.10 Pass 00:00.101
93 Get BLE1 CPU version 0.10 Pass 00:00.104
94 Get BLE2 CPU version 0.10 Pass 00:00.106
95 Start TX (warming up) Pass 00:00.000
96 TesterMCU_Set_ISM_Mux Pass Pass 00:00.022
97 Set TX on pwr = 240 freq = 902000 debug Pass Pass 00:01.641
98 Delay 10000 Pass Pass 00:10.000
99 BLE RX CH 37 Pass 00:00.000
100 ReaderBLE_PreTestConfig Pass Pass 00:07.353
101 ReaderBLEtest ch 37 -42.40 Pass 00:05.953
102 ReaderBLEtest ch 37 ant 1 -50 -42.35 100 Pass 00:07.995
103 ReaderBLEtest ch 37 ant 2 -50 -45.52 100 Pass 00:08.014
104 ReaderBLEtest ch 37 ant 3 -50 -45.96 100 Pass 00:07.871
105 ReaderBLEtest ch 37 ant 4 -50 -43.14 100 Pass 00:08.025
106 ReaderBLEtest ch 37 ant 5 -50 -42.42 100 Pass 00:08.061
107 ReaderBLEtest ch 37 ant 6 -50 -42.45 100 Pass 00:08.043
108 ReaderBLEtest ch 37 ant 7 -50 -42.00 100 Pass 00:08.043
109 BLE RX CH 38 Pass 00:00.000
110 ReaderBLE_PreTestConfig Pass Pass 00:07.358
111 ReaderBLEtest ch 38 -42.97 Pass 00:08.030
112 ReaderBLEtest ch 38 ant 1 -50 -42.44 100 Pass 00:07.952
113 ReaderBLEtest ch 38 ant 2 -50 -43.96 100 Pass 00:08.018
114 ReaderBLEtest ch 38 ant 3 -50 -43.21 100 Pass 00:08.066
115 ReaderBLEtest ch 38 ant 4 -50 -40.77 100 Pass 00:08.033
116 ReaderBLEtest ch 38 ant 5 -50 -42.21 100 Pass 00:08.016
117 ReaderBLEtest ch 38 ant 6 -50 -41.45 100 Pass 00:08.009
118 ReaderBLEtest ch 38 ant 7 -50 -40.87 100 Pass 00:08.000
119 BLE RX CH 39 Pass 00:00.000
120 ReaderBLE_PreTestConfig Pass Pass 00:07.393
121 ReaderBLEtest ch 39 -60.68 Pass 00:09.962
122 ReaderBLEtest ch 39 ant 1 -50 -40.99 100 Pass 00:07.993
123 ReaderBLEtest ch 39 ant 2 -50 -45.57 100 Pass 00:06.038
124 ReaderBLEtest ch 39 ant 3 -50 -43.00 100 Pass 00:06.023
125 ReaderBLEtest ch 39 ant 4 -50 -40.69 100 Pass 00:08.003
126 ReaderBLEtest ch 39 ant 5 -50 -44.63 100 Pass 00:07.962
127 ReaderBLEtest ch 39 ant 6 -50 -45.18 100 Pass 00:08.159
128 ReaderBLEtest ch 39 ant 7 -50 -43.99 100 Pass 00:07.985
129 ReaderBLE_PreTestConfig - stop scan Pass Pass 00:07.376
130 TX Test Pass 00:00.000
131 SetSpectrum Pass Pass 00:00.000
132 Get Last Spectrum Mesurment Freq 901999906.63 Pass 00:00.390
133 Get Last Spectrum Mesurment Amp 20 29.01 100 Pass 00:00.000
134 TX Calibration Pass 00:00.000
135 Reader Tx Warmup target 40 C - 45 C 38 38.5 45 Pass 00:00.101
136 ReaderCTune ( target freq - measure freq) (Hz) 0 0.00 400 Pass 00:47.211
137 C -Tune Selected Xi Xo 114,114 Pass 00:00.000
138 Reader TX Calibration Low 865700000Hz High 915000000Hz Done Pass 01:43.769
139 ReaderTxStoreCalibrationData Pass Pass 00:00.648
140 TX Test - post calibration Pass 00:00.000
141 Restart Reader Pass Pass 00:00.114
142 Delay 6000 Pass Pass 00:06.000
143 ReConnectToReaderTelnet 192.168.0.166 Pass 00:00.374
144 SendReaderConfigFile Pass Pass 00:08.387
145 SetSpectrum Pass Pass 00:00.000
146 Set TX on 30 928000 open Pass Pass 00:01.685
147 Get Last Spectrum Mesurment Freq 928996000 927999907.36 928004000 Pass 00:00.472
148 Get Last Spectrum Mesurment Amp 28 29.04 32 Pass 00:00.000
149 SetSpectrum Pass Pass 00:00.000
150 Set TX on 25 865700 open Pass Pass 00:01.694
151 Get Last Spectrum Mesurment Freq 865796000 865700024.24 865704000 Pass 00:00.480
152 Get Last Spectrum Mesurment Amp 23 24.92 27 Pass 00:00.000
153 SetSpectrum Pass Pass 00:00.000
154 Set TX on 30 865700 open Pass Pass 00:01.690
155 Get Last Spectrum Mesurment Freq 865796000 865700024.24 865704000 Pass 00:00.508
156 Get Last Spectrum Mesurment Amp 27 28.00 32 Pass 00:00.000
157 Set TX off Pass Pass 00:00.315
158 Finalize Pass 00:00.000
159 Finalize Pass Pass 00:00.065
Back to List