GuiSession

stationCode
ReaderFT_01
scandData
000006188,AS000016REVC054424
ATPName
Reader2.0_FullATP_20241112_113709
startTime
11/12/2024 11:30:35
endTime
11/12/2024 11:38:39
Duration
08:04.300
Status
Pass

Test Results

index TestName Min Limit ResultAnswer Max Limit ResultStatus Duration
0 Initialize Pass 00:00.000
1 init Pass Pass 00:03.767
2 PoE : OC Pass 00:00.000
3 PoE : OC : Open circuit test :Turn on the 54V Pass Pass 00:00.190
4 PoE : OC : Set NXP RST Pass Pass 00:00.026
5 Delay 1000ms Pass Pass 00:01.000
6 PoE : OC : Read PoE+ voltage rail (PoE_P_ADC) (mv) 0 Pass 00:00.163
7 PoE : OC : PoE VDD voltage rail (PoE_VDD_ADC) (mv) 1 Pass 00:00.155
8 PoE : OC : PoE VDD voltage rail (PoE_VT15_ADC) (mv) 0 Pass 00:00.153
9 PoE : OC : Measure the current over 54V rail (Vbus54V) (mA) 32 Pass 00:00.032
10 PoE : OC : Read 4.6V rail voltage (ADC_4V6_Load) (mv) 4450 4542 4650 Pass 00:00.030
11 PoE : CC Pass 00:00.000
12 PoE : CC : turn on Load 4.6V rail with external resistor (Load4V6) Pass Pass 00:00.030
13 Delay 100ms Pass Pass 00:00.100
14 PoE : CC : Read PoE+ voltage rail (PoE_P_ADC) (mv) Skip Pass 00:00.000
15 PoE : CC : PoE VDD voltage rail (PoE_VDD_ADC) (mv) Skip Pass 00:00.000
16 PoE : CC : PoE VDD voltage rail (PoE_VT15_ADC) (mv) Skip Pass 00:00.000
17 PoE : CC : Measure the current over 54V rail (Vbus54V) (mA) 232 Pass 00:00.034
18 PoE : CC : Read 4.6V rail voltage (ADC_4V6_Load) (mv) 4287 Pass 00:00.037
19 PoE : CC : turn off Load 4.6V rail with external resistor (Load4V6) Pass Pass 00:00.030
20 PoE : CC : Open circuit test :Turn Off the 54V Pass Pass 00:00.021
21 PA 4.6V : OC Pass 00:00.000
22 PA 4.6V : OC : Turn on the 4.6V high current source (Vbus4V6H) Pass Pass 00:00.023
23 Delay 500ms Pass Pass 00:00.500
24 PA 4.6V : OC : Read 4.6V PA voltage rail 4100 4263 4600 Pass 00:00.034
25 PA 4.6V : OC : Measure the current over 4.6V high current rail 50 203 600 Pass 00:00.025
26 PA 4.6V : CC : Pass 00:00.000
27 PA 4.6V : CC : Load 4.6V PA rail with external resistor Skip Pass 00:00.000
28 Delay 100ms Skip Pass 00:00.000
29 PA 4.6V : CC : Read 4.6V PA voltage rail 2400 Skip 2800 Pass 00:00.000
30 PA 4.6V : CC : Measure the current over 4.6V high current rail 1000 Skip 2000 Pass 00:00.000
31 PA 4.6V : CC : Turn off the external load for 4.6V PA rail Skip Pass 00:00.000
32 MCU LDO : OC Pass 00:00.000
33 MCU LDO : OC : Release NXP RST Pass Pass 00:00.023
34 Delay 500ms Pass Pass 00:00.500
35 MCU LDO : OC : Read 3.5V voltage rail (ADC_3V5_MCU) - (mV) 3300 3545 3600 Pass 00:00.035
36 MCU LDO : OC : Measure the current over 4.6V high current rail (Vbus4V6H) (mA) 15 283 1000 Pass 00:00.031
37 BLE LDO : OC Pass 00:00.000
38 BLE LDO : OC : Release RST of 3.3V BLE LDO (LDO_BLE) Pass Pass 00:00.022
39 Delay 500ms Pass Pass 00:00.500
40 BLE LDO : OC : Read 3.3V BLE voltage rail (ADC_3V3_BLE) - (mV) 3250 3316 3350 Pass 00:00.034
41 BLE LDO : OC : Measure the current over 4.6V high current rail (Vbus4V6H) - (mA) 50 240 1000 Pass 00:00.026
42 LNA LDO : OC Pass 00:00.000
43 LNA LDO : OC : Release RST of 3.3V BLE LDO (LDO_LNA) Pass Pass 00:00.031
44 Delay 100ms Pass Pass 00:00.100
45 LNA LDO : OC : Read 3.3V BLE voltage rail (ADC_3V3_LNA) - (mV) 3250 3310 3350 Pass 00:00.038
46 LNA LDO : OC : Measure the current over 4.6V high current rail (Vbus4V6H) - (mA) 60 235 1000 Pass 00:00.028
47 Flashing NXP Pass 00:00.000
48 TesterMCU_BoardReset Pass Pass 00:00.038
49 Turn on the 4.6V high current source (Vbus4V6H) Pass Pass 00:00.030
50 Set SWD splitter to Out1 Pass Pass 00:00.036
51 Release NXP reset line Pass Pass 00:00.036
52 Jflash_Programming jlink2 workaround Pass Pass 00:02.015
53 Jflash_Programming jlink2 nxp boot Pass Pass 00:01.779
54 Jflash_Programming jlink2 nxp application Pass Pass 00:09.696
55 Set NXP reset line Pass Pass 00:00.035
56 Delay 500 Pass Pass 00:00.500
57 Release NXP reset line Pass Pass 00:00.034
58 Delay 500 Pass Pass 00:00.500
59 Flashing ISM Pass 00:00.000
60 Release all pinout Pass Pass 00:00.034
61 Delay 4000 Pass Pass 00:04.000
62 Set SWD splitter to Out2 Pass Pass 00:00.029
63 Jflash_Programming jlink2 TX boot Pass Pass 00:00.547
64 Jflash_Programming jlink2 TX application Pass Pass 00:00.966
65 Flashing BLE 1 Pass 00:00.000
66 Set SWD splitter to Out1 Pass Pass 00:00.028
67 Release RST of 3.3V BLE LDO (LDO_BLE) Pass Pass 00:00.029
68 Jflash_Programming jlink1 ble Pass Pass 00:01.227
69 Flashing BLE 2 Pass 00:00.000
70 Set SWD splitter to Out2 Pass Pass 00:00.022
71 Jflash_Programming jlink1 ble Pass Pass 00:01.222
72 Flashing BLE 3 Pass 00:00.000
73 Set SWD splitter to Out3 Pass Pass 00:00.036
74 Jflash_Programming jlink1 ble Pass Pass 00:01.231
75 Reader PWR reset Pass 00:00.000
76 Turn OFF the 4.6V high current source (Vbus4V6H) Pass Pass 00:00.030
77 Release NXP reset line Pass Pass 00:00.026
78 Release all pinout Pass Pass 00:00.039
79 Turn ON the 4.6V high current source (Vbus4V6H) Pass Pass 00:00.023
80 Delay 6000 Pass Pass 00:06.000
81 Reader Connect Pass 00:00.000
82 ConnectToReaderTelnet 192.168.0.161 Pass 00:00.322
83 ReaderSetSerialNumber 000006188 Pass 00:00.331
84 ReaderSetMacAddress 1063A390022D Pass 00:00.239
85 Restart Reader Pass Pass 00:00.102
86 Delay 6000 Pass Pass 00:06.000
87 ReConnectToReaderTelnet 192.168.0.161 Pass 00:00.316
88 ReaderGetMacAddress 1063A390022D Pass 00:00.212
89 SendReaderConfigFile Pass Pass 00:09.408
90 Get Main CPU version 2.1.1+1029 Pass 00:00.107
91 Get TX CPU version 0.15 Pass 00:00.731
92 Get BLE0 CPU version 0.10 Pass 00:00.101
93 Get BLE1 CPU version 0.10 Pass 00:00.108
94 Get BLE2 CPU version 0.10 Pass 00:00.112
95 Start TX (warming up) Pass 00:00.000
96 TesterMCU_Set_ISM_Mux Pass Pass 00:00.037
97 Set TX on pwr = 240 freq = 902000 debug Pass Pass 00:01.681
98 Delay 10000 Pass Pass 00:10.000
99 BLE RX CH 37 Pass 00:00.000
100 ReaderBLE_PreTestConfig Pass Pass 00:07.438
101 ReaderBLEtest ch 37 -43.08 Pass 00:08.120
102 ReaderBLEtest ch 37 ant 1 -50 -43.06 100 Pass 00:08.135
103 ReaderBLEtest ch 37 ant 2 -50 -45.81 100 Pass 00:08.134
104 ReaderBLEtest ch 37 ant 3 -50 -45.39 100 Pass 00:08.129
105 ReaderBLEtest ch 37 ant 4 -50 -44.20 100 Pass 00:08.145
106 ReaderBLEtest ch 37 ant 5 -50 -42.29 100 Pass 00:08.109
107 ReaderBLEtest ch 37 ant 6 -50 -42.00 100 Pass 00:08.113
108 ReaderBLEtest ch 37 ant 7 -50 -42.00 100 Pass 00:08.094
109 BLE RX CH 38 Pass 00:00.000
110 ReaderBLE_PreTestConfig Pass Pass 00:07.448
111 ReaderBLEtest ch 38 -52.03 Pass 00:12.315
112 ReaderBLEtest ch 38 ant 1 -50 -44.78 100 Pass 00:06.025
113 ReaderBLEtest ch 38 ant 2 -50 -45.03 100 Pass 00:08.106
114 ReaderBLEtest ch 38 ant 3 -50 -43.84 100 Pass 00:08.127
115 ReaderBLEtest ch 38 ant 4 -50 -42.00 100 Pass 00:08.096
116 ReaderBLEtest ch 38 ant 5 -50 -43.04 100 Pass 00:06.019
117 ReaderBLEtest ch 38 ant 6 -50 -42.06 100 Pass 00:08.148
118 ReaderBLEtest ch 38 ant 7 -50 -41.33 100 Pass 00:08.140
119 BLE RX CH 39 Pass 00:00.000
120 ReaderBLE_PreTestConfig Pass Pass 00:07.437
121 ReaderBLEtest ch 39 -42.00 Pass 00:08.131
122 ReaderBLEtest ch 39 ant 1 -50 -42.00 100 Pass 00:08.110
123 ReaderBLEtest ch 39 ant 2 -50 -46.17 100 Pass 00:06.039
124 ReaderBLEtest ch 39 ant 3 -50 -43.99 100 Pass 00:06.043
125 ReaderBLEtest ch 39 ant 4 -50 -41.59 100 Pass 00:06.028
126 ReaderBLEtest ch 39 ant 5 -50 -45.33 100 Pass 00:08.135
127 ReaderBLEtest ch 39 ant 6 -50 -46.11 100 Pass 00:08.126
128 ReaderBLEtest ch 39 ant 7 -50 -44.12 100 Pass 00:08.129
129 ReaderBLE_PreTestConfig - stop scan Pass Pass 00:07.436
130 TX Test Pass 00:00.000
131 SetSpectrum Pass Pass 00:00.000
132 Get Last Spectrum Mesurment Freq 901999906.63 Pass 00:00.484
133 Get Last Spectrum Mesurment Amp 20 28.97 100 Pass 00:00.000
134 TX Calibration Pass 00:00.000
135 Reader Tx Warmup target 40 C - 45 C 38 40 45 Pass 00:00.114
136 ReaderCTune ( target freq - measure freq) (Hz) 0 178.02 400 Pass 00:52.214
137 C -Tune Selected Xi Xo 100,101 Pass 00:00.000
138 Reader TX Calibration Low 865700000Hz High 915000000Hz Done Pass 01:47.099
139 ReaderTxStoreCalibrationData Pass Pass 00:00.614
140 TX Test - post calibration Pass 00:00.000
141 Restart Reader Pass Pass 00:00.115
142 Delay 6000 Pass Pass 00:06.000
143 ReConnectToReaderTelnet 192.168.0.161 Pass 00:00.352
144 SendReaderConfigFile Pass Pass 00:09.222
145 SetSpectrum Pass Pass 00:00.000
146 Set TX on 30 928000 open Pass Pass 00:01.691
147 Get Last Spectrum Mesurment Freq 928996000 928001093.60 928004000 Pass 00:00.469
148 Get Last Spectrum Mesurment Amp 28 29.06 32 Pass 00:00.000
149 SetSpectrum Pass Pass 00:00.000
150 Set TX on 25 865700 open Pass Pass 00:01.697
151 Get Last Spectrum Mesurment Freq 865796000 865700973.23 865704000 Pass 00:00.499
152 Get Last Spectrum Mesurment Amp 23 25.44 27 Pass 00:00.000
153 SetSpectrum Pass Pass 00:00.000
154 Set TX on 30 865700 open Pass Pass 00:01.688
155 Get Last Spectrum Mesurment Freq 865796000 865700973.23 865704000 Pass 00:00.505
156 Get Last Spectrum Mesurment Amp 27 28.31 32 Pass 00:00.000
157 Set TX off Pass Pass 00:00.312
158 Finalize Pass 00:00.000
159 Finalize Pass Pass 00:00.072
Back to List