GuiSession

stationCode
ReaderFT_01
scandData
000005884,AS000016REVC054424
ATPName
Reader2.0_FullATP_20241112_113709
startTime
11/12/2024 11:21:07
endTime
11/12/2024 11:29:04
Duration
07:56.880
Status
Pass

Test Results

index TestName Min Limit ResultAnswer Max Limit ResultStatus Duration
0 Initialize Pass 00:00.000
1 init Pass Pass 00:03.761
2 PoE : OC Pass 00:00.000
3 PoE : OC : Open circuit test :Turn on the 54V Pass Pass 00:00.183
4 PoE : OC : Set NXP RST Pass Pass 00:00.032
5 Delay 1000ms Pass Pass 00:01.000
6 PoE : OC : Read PoE+ voltage rail (PoE_P_ADC) (mv) 0 Pass 00:00.164
7 PoE : OC : PoE VDD voltage rail (PoE_VDD_ADC) (mv) 1 Pass 00:00.159
8 PoE : OC : PoE VDD voltage rail (PoE_VT15_ADC) (mv) 0 Pass 00:00.154
9 PoE : OC : Measure the current over 54V rail (Vbus54V) (mA) 31 Pass 00:00.028
10 PoE : OC : Read 4.6V rail voltage (ADC_4V6_Load) (mv) 4450 4526 4650 Pass 00:00.028
11 PoE : CC Pass 00:00.000
12 PoE : CC : turn on Load 4.6V rail with external resistor (Load4V6) Pass Pass 00:00.029
13 Delay 100ms Pass Pass 00:00.100
14 PoE : CC : Read PoE+ voltage rail (PoE_P_ADC) (mv) Skip Pass 00:00.000
15 PoE : CC : PoE VDD voltage rail (PoE_VDD_ADC) (mv) Skip Pass 00:00.000
16 PoE : CC : PoE VDD voltage rail (PoE_VT15_ADC) (mv) Skip Pass 00:00.000
17 PoE : CC : Measure the current over 54V rail (Vbus54V) (mA) 229 Pass 00:00.035
18 PoE : CC : Read 4.6V rail voltage (ADC_4V6_Load) (mv) 4264 Pass 00:00.031
19 PoE : CC : turn off Load 4.6V rail with external resistor (Load4V6) Pass Pass 00:00.030
20 PoE : CC : Open circuit test :Turn Off the 54V Pass Pass 00:00.030
21 PA 4.6V : OC Pass 00:00.000
22 PA 4.6V : OC : Turn on the 4.6V high current source (Vbus4V6H) Pass Pass 00:00.030
23 Delay 500ms Pass Pass 00:00.500
24 PA 4.6V : OC : Read 4.6V PA voltage rail 4100 4268 4600 Pass 00:00.029
25 PA 4.6V : OC : Measure the current over 4.6V high current rail 50 200 600 Pass 00:00.031
26 PA 4.6V : CC : Pass 00:00.000
27 PA 4.6V : CC : Load 4.6V PA rail with external resistor Skip Pass 00:00.000
28 Delay 100ms Skip Pass 00:00.000
29 PA 4.6V : CC : Read 4.6V PA voltage rail 2400 Skip 2800 Pass 00:00.000
30 PA 4.6V : CC : Measure the current over 4.6V high current rail 1000 Skip 2000 Pass 00:00.000
31 PA 4.6V : CC : Turn off the external load for 4.6V PA rail Skip Pass 00:00.000
32 MCU LDO : OC Pass 00:00.000
33 MCU LDO : OC : Release NXP RST Pass Pass 00:00.022
34 Delay 500ms Pass Pass 00:00.500
35 MCU LDO : OC : Read 3.5V voltage rail (ADC_3V5_MCU) - (mV) 3300 3547 3600 Pass 00:00.034
36 MCU LDO : OC : Measure the current over 4.6V high current rail (Vbus4V6H) (mA) 15 315 1000 Pass 00:00.025
37 BLE LDO : OC Pass 00:00.000
38 BLE LDO : OC : Release RST of 3.3V BLE LDO (LDO_BLE) Pass Pass 00:00.036
39 Delay 500ms Pass Pass 00:00.500
40 BLE LDO : OC : Read 3.3V BLE voltage rail (ADC_3V3_BLE) - (mV) 3250 3309 3350 Pass 00:00.034
41 BLE LDO : OC : Measure the current over 4.6V high current rail (Vbus4V6H) - (mA) 50 242 1000 Pass 00:00.029
42 LNA LDO : OC Pass 00:00.000
43 LNA LDO : OC : Release RST of 3.3V BLE LDO (LDO_LNA) Pass Pass 00:00.031
44 Delay 100ms Pass Pass 00:00.100
45 LNA LDO : OC : Read 3.3V BLE voltage rail (ADC_3V3_LNA) - (mV) 3250 3316 3350 Pass 00:00.028
46 LNA LDO : OC : Measure the current over 4.6V high current rail (Vbus4V6H) - (mA) 60 243 1000 Pass 00:00.022
47 Flashing NXP Pass 00:00.000
48 TesterMCU_BoardReset Pass Pass 00:00.029
49 Turn on the 4.6V high current source (Vbus4V6H) Pass Pass 00:00.032
50 Set SWD splitter to Out1 Pass Pass 00:00.022
51 Release NXP reset line Pass Pass 00:00.033
52 Jflash_Programming jlink2 workaround Pass Pass 00:02.011
53 Jflash_Programming jlink2 nxp boot Pass Pass 00:01.724
54 Jflash_Programming jlink2 nxp application Pass Pass 00:09.979
55 Set NXP reset line Pass Pass 00:00.030
56 Delay 500 Pass Pass 00:00.500
57 Release NXP reset line Pass Pass 00:00.032
58 Delay 500 Pass Pass 00:00.500
59 Flashing ISM Pass 00:00.000
60 Release all pinout Pass Pass 00:00.036
61 Delay 4000 Pass Pass 00:04.000
62 Set SWD splitter to Out2 Pass Pass 00:00.024
63 Jflash_Programming jlink2 TX boot Pass Pass 00:00.538
64 Jflash_Programming jlink2 TX application Pass Pass 00:00.971
65 Flashing BLE 1 Pass 00:00.000
66 Set SWD splitter to Out1 Pass Pass 00:00.028
67 Release RST of 3.3V BLE LDO (LDO_BLE) Pass Pass 00:00.029
68 Jflash_Programming jlink1 ble Pass Pass 00:01.252
69 Flashing BLE 2 Pass 00:00.000
70 Set SWD splitter to Out2 Pass Pass 00:00.029
71 Jflash_Programming jlink1 ble Pass Pass 00:01.234
72 Flashing BLE 3 Pass 00:00.000
73 Set SWD splitter to Out3 Pass Pass 00:00.036
74 Jflash_Programming jlink1 ble Pass Pass 00:01.253
75 Reader PWR reset Pass 00:00.000
76 Turn OFF the 4.6V high current source (Vbus4V6H) Pass Pass 00:00.025
77 Release NXP reset line Pass Pass 00:00.029
78 Release all pinout Pass Pass 00:00.024
79 Turn ON the 4.6V high current source (Vbus4V6H) Pass Pass 00:00.029
80 Delay 6000 Pass Pass 00:06.000
81 Reader Connect Pass 00:00.000
82 ConnectToReaderTelnet 192.168.0.160 Pass 00:00.355
83 ReaderSetSerialNumber 000005884 Pass 00:00.327
84 ReaderSetMacAddress 1063A39002A0 Pass 00:00.361
85 Restart Reader Pass Pass 00:00.103
86 Delay 6000 Pass Pass 00:06.000
87 ReConnectToReaderTelnet 192.168.0.160 Pass 00:00.329
88 ReaderGetMacAddress 1063A39002A0 Pass 00:00.210
89 SendReaderConfigFile Pass Pass 00:09.400
90 Get Main CPU version 2.1.1+1029 Pass 00:00.111
91 Get TX CPU version 0.15 Pass 00:00.730
92 Get BLE0 CPU version 0.10 Pass 00:00.110
93 Get BLE1 CPU version 0.10 Pass 00:00.719
94 Get BLE2 CPU version 0.10 Pass 00:00.110
95 Start TX (warming up) Pass 00:00.000
96 TesterMCU_Set_ISM_Mux Pass Pass 00:00.035
97 Set TX on pwr = 240 freq = 902000 debug Pass Pass 00:01.685
98 Delay 10000 Pass Pass 00:10.000
99 BLE RX CH 37 Pass 00:00.000
100 ReaderBLE_PreTestConfig Pass Pass 00:07.447
101 ReaderBLEtest ch 37 -43.61 Pass 00:08.103
102 ReaderBLEtest ch 37 ant 1 -50 -43.73 100 Pass 00:08.101
103 ReaderBLEtest ch 37 ant 2 -50 -45.82 100 Pass 00:08.119
104 ReaderBLEtest ch 37 ant 3 -50 -45.60 100 Pass 00:08.144
105 ReaderBLEtest ch 37 ant 4 -50 -44.09 100 Pass 00:08.126
106 ReaderBLEtest ch 37 ant 5 -50 -43.47 100 Pass 00:08.117
107 ReaderBLEtest ch 37 ant 6 -50 -42.00 100 Pass 00:08.117
108 ReaderBLEtest ch 37 ant 7 -50 -42.64 100 Pass 00:06.037
109 BLE RX CH 38 Pass 00:00.000
110 ReaderBLE_PreTestConfig Pass Pass 00:07.453
111 ReaderBLEtest ch 38 -53.08 Pass 00:10.219
112 ReaderBLEtest ch 38 ant 1 -50 -44.00 100 Pass 00:08.095
113 ReaderBLEtest ch 38 ant 2 -50 -44.52 100 Pass 00:06.037
114 ReaderBLEtest ch 38 ant 3 -50 -42.99 100 Pass 00:08.090
115 ReaderBLEtest ch 38 ant 4 -50 -42.00 100 Pass 00:08.105
116 ReaderBLEtest ch 38 ant 5 -50 -42.86 100 Pass 00:06.038
117 ReaderBLEtest ch 38 ant 6 -50 -41.57 100 Pass 00:08.132
118 ReaderBLEtest ch 38 ant 7 -50 -41.03 100 Pass 00:08.135
119 BLE RX CH 39 Pass 00:00.000
120 ReaderBLE_PreTestConfig Pass Pass 00:07.439
121 ReaderBLEtest ch 39 -40.00 Pass 00:08.113
122 ReaderBLEtest ch 39 ant 1 -50 -40.00 100 Pass 00:08.115
123 ReaderBLEtest ch 39 ant 2 -50 -45.00 100 Pass 00:06.013
124 ReaderBLEtest ch 39 ant 3 -50 -42.18 100 Pass 00:08.126
125 ReaderBLEtest ch 39 ant 4 -50 -41.09 100 Pass 00:06.034
126 ReaderBLEtest ch 39 ant 5 -50 -44.90 100 Pass 00:08.110
127 ReaderBLEtest ch 39 ant 6 -50 -44.93 100 Pass 00:08.121
128 ReaderBLEtest ch 39 ant 7 -50 -43.12 100 Pass 00:08.120
129 ReaderBLE_PreTestConfig - stop scan Pass Pass 00:07.453
130 TX Test Pass 00:00.000
131 SetSpectrum Pass Pass 00:00.000
132 Get Last Spectrum Mesurment Freq 901999669.38 Pass 00:00.480
133 Get Last Spectrum Mesurment Amp 20 28.86 100 Pass 00:00.000
134 TX Calibration Pass 00:00.000
135 Reader Tx Warmup target 40 C - 45 C 38 39.75 45 Pass 00:00.104
136 ReaderCTune ( target freq - measure freq) (Hz) 0 89.01 400 Pass 00:47.758
137 C -Tune Selected Xi Xo 104,105 Pass 00:00.000
138 Reader TX Calibration Low 865700000Hz High 915000000Hz Done Pass 01:47.145
139 ReaderTxStoreCalibrationData Pass Pass 00:00.577
140 TX Test - post calibration Pass 00:00.000
141 Restart Reader Pass Pass 00:00.103
142 Delay 6000 Pass Pass 00:06.000
143 ReConnectToReaderTelnet 192.168.0.160 Pass 00:00.331
144 SendReaderConfigFile Pass Pass 00:06.755
145 SetSpectrum Pass Pass 00:00.000
146 Set TX on 30 928000 open Pass Pass 00:01.690
147 Get Last Spectrum Mesurment Freq 928996000 927999907.36 928004000 Pass 00:00.478
148 Get Last Spectrum Mesurment Amp 28 28.56 32 Pass 00:00.000
149 SetSpectrum Pass Pass 00:00.000
150 Set TX on 25 865700 open Pass Pass 00:01.699
151 Get Last Spectrum Mesurment Freq 865796000 865699786.99 865704000 Pass 00:00.483
152 Get Last Spectrum Mesurment Amp 23 25.35 27 Pass 00:00.000
153 SetSpectrum Pass Pass 00:00.000
154 Set TX on 30 865700 open Pass Pass 00:01.691
155 Get Last Spectrum Mesurment Freq 865796000 865699786.99 865704000 Pass 00:00.504
156 Get Last Spectrum Mesurment Amp 27 27.70 32 Pass 00:00.000
157 Set TX off Pass Pass 00:00.311
158 Finalize Pass 00:00.000
159 Finalize Pass Pass 00:00.077
Back to List