GuiSession

stationCode
ReaderFT_01
scandData
000005331,AS000016REVC054424
ATPName
Reader2.0_FullATP_20241112_085816
startTime
11/12/2024 07:04:47
endTime
11/12/2024 07:12:16
Duration
07:28.967
Status
Fail

Test Results

index TestName Min Limit ResultAnswer Max Limit ResultStatus Duration
0 Initialize Pass 00:00.000
1 init Pass Pass 00:03.835
2 PoE : OC Pass 00:00.000
3 PoE : OC : Open circuit test :Turn on the 54V Pass Pass 00:00.180
4 PoE : OC : Set NXP RST Pass Pass 00:00.023
5 Delay 1000ms Pass Pass 00:01.000
6 PoE : OC : Read PoE+ voltage rail (PoE_P_ADC) (mv) 0 Pass 00:00.166
7 PoE : OC : PoE VDD voltage rail (PoE_VDD_ADC) (mv) 1 Pass 00:00.154
8 PoE : OC : PoE VDD voltage rail (PoE_VT15_ADC) (mv) 0 Pass 00:00.154
9 PoE : OC : Measure the current over 54V rail (Vbus54V) (mA) 32 Pass 00:00.028
10 PoE : OC : Read 4.6V rail voltage (ADC_4V6_Load) (mv) 4450 4549 4650 Pass 00:00.028
11 PoE : CC Pass 00:00.000
12 PoE : CC : turn on Load 4.6V rail with external resistor (Load4V6) Pass Pass 00:00.030
13 Delay 100ms Pass Pass 00:00.100
14 PoE : CC : Read PoE+ voltage rail (PoE_P_ADC) (mv) Skip Pass 00:00.000
15 PoE : CC : PoE VDD voltage rail (PoE_VDD_ADC) (mv) Skip Pass 00:00.000
16 PoE : CC : PoE VDD voltage rail (PoE_VT15_ADC) (mv) Skip Pass 00:00.000
17 PoE : CC : Measure the current over 54V rail (Vbus54V) (mA) 233 Pass 00:00.032
18 PoE : CC : Read 4.6V rail voltage (ADC_4V6_Load) (mv) 4305 Pass 00:00.040
19 PoE : CC : turn off Load 4.6V rail with external resistor (Load4V6) Pass Pass 00:00.022
20 PoE : CC : Open circuit test :Turn Off the 54V Pass Pass 00:00.033
21 PA 4.6V : OC Pass 00:00.000
22 PA 4.6V : OC : Turn on the 4.6V high current source (Vbus4V6H) Pass Pass 00:00.023
23 Delay 500ms Pass Pass 00:00.500
24 PA 4.6V : OC : Read 4.6V PA voltage rail 4100 4267 4600 Pass 00:00.036
25 PA 4.6V : OC : Measure the current over 4.6V high current rail 50 200 600 Pass 00:00.030
26 PA 4.6V : CC : Pass 00:00.000
27 PA 4.6V : CC : Load 4.6V PA rail with external resistor Skip Pass 00:00.000
28 Delay 100ms Skip Pass 00:00.000
29 PA 4.6V : CC : Read 4.6V PA voltage rail 2400 Skip 2800 Pass 00:00.000
30 PA 4.6V : CC : Measure the current over 4.6V high current rail 1000 Skip 2000 Pass 00:00.000
31 PA 4.6V : CC : Turn off the external load for 4.6V PA rail Skip Pass 00:00.000
32 MCU LDO : OC Pass 00:00.000
33 MCU LDO : OC : Release NXP RST Pass Pass 00:00.035
34 Delay 500ms Pass Pass 00:00.500
35 MCU LDO : OC : Read 3.5V voltage rail (ADC_3V5_MCU) - (mV) 3300 3536 3600 Pass 00:00.036
36 MCU LDO : OC : Measure the current over 4.6V high current rail (Vbus4V6H) (mA) 15 301 1000 Pass 00:00.035
37 BLE LDO : OC Pass 00:00.000
38 BLE LDO : OC : Release RST of 3.3V BLE LDO (LDO_BLE) Pass Pass 00:00.029
39 Delay 500ms Pass Pass 00:00.500
40 BLE LDO : OC : Read 3.3V BLE voltage rail (ADC_3V3_BLE) - (mV) 3250 3317 3350 Pass 00:00.028
41 BLE LDO : OC : Measure the current over 4.6V high current rail (Vbus4V6H) - (mA) 50 313 1000 Pass 00:00.034
42 LNA LDO : OC Pass 00:00.000
43 LNA LDO : OC : Release RST of 3.3V BLE LDO (LDO_LNA) Pass Pass 00:00.028
44 Delay 100ms Pass Pass 00:00.100
45 LNA LDO : OC : Read 3.3V BLE voltage rail (ADC_3V3_LNA) - (mV) 3250 3313 3350 Pass 00:00.040
46 LNA LDO : OC : Measure the current over 4.6V high current rail (Vbus4V6H) - (mA) 60 232 1000 Pass 00:00.034
47 Flashing NXP Pass 00:00.000
48 TesterMCU_BoardReset Pass Pass 00:00.037
49 Turn on the 4.6V high current source (Vbus4V6H) Pass Pass 00:00.027
50 Set SWD splitter to Out1 Pass Pass 00:00.035
51 Release NXP reset line Pass Pass 00:00.034
52 Jflash_Programming jlink2 workaround Pass Pass 00:02.012
53 Jflash_Programming jlink2 nxp boot Pass Pass 00:01.761
54 Jflash_Programming jlink2 nxp application Pass Pass 00:09.856
55 Set NXP reset line Pass Pass 00:00.031
56 Delay 500 Pass Pass 00:00.500
57 Release NXP reset line Pass Pass 00:00.030
58 Delay 500 Pass Pass 00:00.500
59 Flashing ISM Pass 00:00.000
60 Release all pinout Pass Pass 00:00.037
61 Delay 4000 Pass Pass 00:04.000
62 Set SWD splitter to Out2 Pass Pass 00:00.035
63 Jflash_Programming jlink2 TX boot Pass Pass 00:00.518
64 Jflash_Programming jlink2 TX application Pass Pass 00:00.942
65 Flashing BLE 1 Pass 00:00.000
66 Set SWD splitter to Out1 Pass Pass 00:00.036
67 Release RST of 3.3V BLE LDO (LDO_BLE) Pass Pass 00:00.025
68 Jflash_Programming jlink1 ble Pass Pass 00:01.231
69 Flashing BLE 2 Pass 00:00.000
70 Set SWD splitter to Out2 Pass Pass 00:00.026
71 Jflash_Programming jlink1 ble Pass Pass 00:01.324
72 Flashing BLE 3 Pass 00:00.000
73 Set SWD splitter to Out3 Pass Pass 00:00.023
74 Jflash_Programming jlink1 ble Pass Pass 00:01.237
75 Reader PWR reset Pass 00:00.000
76 Turn OFF the 4.6V high current source (Vbus4V6H) Pass Pass 00:00.027
77 Release NXP reset line Pass Pass 00:00.027
78 Release all pinout Pass Pass 00:00.033
79 Turn ON the 4.6V high current source (Vbus4V6H) Pass Pass 00:00.033
80 Delay 6000 Pass Pass 00:06.000
81 Reader Connect Pass 00:00.000
82 ConnectToReaderTelnet 192.168.0.151 Pass 00:00.350
83 ReaderSetSerialNumber 000005331 Pass 00:00.325
84 ReaderSetMacAddress 1063A39000EB Pass 00:00.364
85 Restart Reader Pass Pass 00:00.110
86 Delay 6000 Pass Pass 00:06.000
87 ReConnectToReaderTelnet 192.168.0.151 Pass 00:00.339
88 ReaderGetMacAddress 1063A39000EB Pass 00:00.210
89 SendReaderConfigFile Pass Pass 00:08.606
90 Get Main CPU version 2.1.1+1029 Pass 00:00.739
91 Get TX CPU version 0.15 Pass 00:00.105
92 Get BLE0 CPU version 0.10 Pass 00:00.111
93 Get BLE1 CPU version 0.10 Pass 00:00.715
94 Get BLE2 CPU version 0.10 Pass 00:00.727
95 Start TX (warming up) Pass 00:00.000
96 TesterMCU_Set_ISM_Mux Pass Pass 00:00.025
97 Set TX on pwr = 240 freq = 902000 debug Pass Pass 00:01.678
98 Delay 10000 Pass Pass 00:10.000
99 BLE RX CH 37 Pass 00:00.000
100 ReaderBLE_PreTestConfig Pass Pass 00:07.444
101 ReaderBLEtest ch 37 -52.09 Pass 00:10.171
102 ReaderBLEtest ch 37 ant 1 -50 -41.67 100 Pass 00:08.079
103 ReaderBLEtest ch 37 ant 2 -50 -43.93 100 Pass 00:08.091
104 ReaderBLEtest ch 37 ant 3 -50 -43.84 100 Pass 00:08.043
105 ReaderBLEtest ch 37 ant 4 -50 -40.66 100 Pass 00:08.069
106 ReaderBLEtest ch 37 ant 5 -50 -41.58 100 Pass 00:08.038
107 ReaderBLEtest ch 37 ant 6 -50 -41.00 100 Pass 00:05.968
108 ReaderBLEtest ch 37 ant 7 -50 -40.21 100 Pass 00:06.017
109 BLE RX CH 38 Pass 00:00.000
110 ReaderBLE_PreTestConfig Pass Pass 00:07.432
111 ReaderBLEtest ch 38 -42.00 Pass 00:05.980
112 ReaderBLEtest ch 38 ant 1 -50 -42.00 100 Pass 00:05.996
113 ReaderBLEtest ch 38 ant 2 -50 -43.00 100 Pass 00:06.012
114 ReaderBLEtest ch 38 ant 3 -50 -42.00 100 Pass 00:05.996
115 ReaderBLEtest ch 38 ant 4 -50 -39.98 100 Pass 00:05.997
116 ReaderBLEtest ch 38 ant 5 -50 -41.06 100 Pass 00:08.045
117 ReaderBLEtest ch 38 ant 6 -50 -40.18 100 Pass 00:05.985
118 ReaderBLEtest ch 38 ant 7 -50 -39.95 100 Pass 00:08.061
119 BLE RX CH 39 Pass 00:00.000
120 ReaderBLE_PreTestConfig Pass Pass 00:07.444
121 ReaderBLEtest ch 39 -40.00 Pass 00:06.002
122 ReaderBLEtest ch 39 ant 1 -50 -40.11 100 Pass 00:05.980
123 ReaderBLEtest ch 39 ant 2 -50 -45.00 100 Pass 00:08.046
124 ReaderBLEtest ch 39 ant 3 -50 -42.00 100 Pass 00:06.005
125 ReaderBLEtest ch 39 ant 4 -50 -39.94 100 Pass 00:05.998
126 ReaderBLEtest ch 39 ant 5 -50 -44.89 100 Pass 00:05.988
127 ReaderBLEtest ch 39 ant 6 -50 -44.94 100 Pass 00:05.993
128 ReaderBLEtest ch 39 ant 7 -50 -42.83 100 Pass 00:06.007
129 ReaderBLE_PreTestConfig - stop scan Pass Pass 00:07.429
130 TX Test Pass 00:00.000
131 SetSpectrum Pass Pass 00:00.002
132 Get Last Spectrum Mesurment Freq 901999906.63 Pass 00:00.467
133 Get Last Spectrum Mesurment Amp 20 29.00 100 Pass 00:00.000
134 TX Calibration Pass 00:00.000
135 Reader Tx Warmup target 40 C - 45 C 38 38.12 45 Pass 00:00.108
136 ReaderCTune ( target freq - measure freq) (Hz) 0 89.01 400 Pass 00:46.438
137 C -Tune Selected Xi Xo 105,107 Pass 00:00.001
138 Reader TX Calibration Low 865700000Hz High 928000000Hz Done Pass 01:46.527
139 ReaderTxStoreCalibrationData Pass Pass 00:00.684
140 TX Test - post calibration Pass 00:00.000
141 Restart Reader Pass Pass 00:00.107
142 Delay 6000 Pass Pass 00:06.000
143 ReConnectToReaderTelnet 192.168.0.151 Pass 00:00.450
144 SendReaderConfigFile Pass Pass 00:09.692
145 SetSpectrum Pass Pass 00:00.000
146 Set TX on 30 928000 open Pass Pass 00:01.669
147 Get Last Spectrum Mesurment Freq 928996000 927999670.11 928004000 Pass 00:00.426
148 Get Last Spectrum Mesurment Amp 28 28.69 32 Pass 00:00.000
149 SetSpectrum Pass Pass 00:00.000
150 Set TX on 25 865700 open Pass Pass 00:01.676
151 Get Last Spectrum Mesurment Freq 865796000 865699786.99 865704000 Pass 00:00.452
152 Get Last Spectrum Mesurment Amp 23 24.89 27 Pass 00:00.000
153 SetSpectrum Pass Pass 00:00.000
154 Set TX on 30 865700 open Pass Pass 00:01.682
155 Get Last Spectrum Mesurment Freq 865796000 865699786.99 865704000 Pass 00:00.515
156 Get Last Spectrum Mesurment Amp 28 27.82 32 Fail 00:00.000
Back to List