GuiSession

stationCode
ReaderFT_01
scandData
000005610,AS000016REVD01
ATPName
Reader2.0_FullATP_20241110_112301
startTime
11/11/2024 09:42:35
endTime
11/11/2024 10:00:07
Duration
17:32.269
Status
Error

Test Results

index TestName Min Limit ResultAnswer Max Limit ResultStatus Duration
0 Initialize Pass 00:00.000
1 init Pass Pass 00:03.774
2 PoE : OC Pass 00:00.000
3 PoE : OC : Open circuit test :Turn on the 54V Pass Pass 00:00.201
4 PoE : OC : Set NXP RST Pass Pass 00:00.021
5 Delay 1000ms Pass Pass 00:01.000
6 PoE : OC : Read PoE+ voltage rail (PoE_P_ADC) (mv) 0 Pass 00:00.157
7 PoE : OC : PoE VDD voltage rail (PoE_VDD_ADC) (mv) 1 Pass 00:00.156
8 PoE : OC : PoE VDD voltage rail (PoE_VT15_ADC) (mv) 0 Pass 00:00.158
9 PoE : OC : Measure the current over 54V rail (Vbus54V) (mA) 30 Pass 00:00.026
10 PoE : OC : Read 4.6V rail voltage (ADC_4V6_Load) (mv) 4450 4516 4650 Pass 00:00.028
11 PoE : CC Pass 00:00.000
12 PoE : CC : turn on Load 4.6V rail with external resistor (Load4V6) Pass Pass 00:00.037
13 Delay 100ms Pass Pass 00:00.100
14 PoE : CC : Read PoE+ voltage rail (PoE_P_ADC) (mv) Skip Pass 00:00.000
15 PoE : CC : PoE VDD voltage rail (PoE_VDD_ADC) (mv) Skip Pass 00:00.000
16 PoE : CC : PoE VDD voltage rail (PoE_VT15_ADC) (mv) Skip Pass 00:00.000
17 PoE : CC : Measure the current over 54V rail (Vbus54V) (mA) 228 Pass 00:00.035
18 PoE : CC : Read 4.6V rail voltage (ADC_4V6_Load) (mv) 4281 Pass 00:00.037
19 PoE : CC : turn off Load 4.6V rail with external resistor (Load4V6) Pass Pass 00:00.036
20 PoE : CC : Open circuit test :Turn Off the 54V Pass Pass 00:00.032
21 PA 4.6V : OC Pass 00:00.000
22 PA 4.6V : OC : Turn on the 4.6V high current source (Vbus4V6H) Pass Pass 00:00.034
23 Delay 500ms Pass Pass 00:00.500
24 PA 4.6V : OC : Read 4.6V PA voltage rail 4100 4496 4600 Pass 00:00.035
25 PA 4.6V : OC : Measure the current over 4.6V high current rail 50 181 600 Pass 00:00.033
26 PA 4.6V : CC : Pass 00:00.000
27 PA 4.6V : CC : Load 4.6V PA rail with external resistor Skip Pass 00:00.000
28 Delay 100ms Skip Pass 00:00.000
29 PA 4.6V : CC : Read 4.6V PA voltage rail 2400 Skip 2800 Pass 00:00.000
30 PA 4.6V : CC : Measure the current over 4.6V high current rail 1000 Skip 2000 Pass 00:00.000
31 PA 4.6V : CC : Turn off the external load for 4.6V PA rail Skip Pass 00:00.000
32 MCU LDO : OC Pass 00:00.000
33 MCU LDO : OC : Release NXP RST Pass Pass 00:00.031
34 Delay 500ms Pass Pass 00:00.500
35 MCU LDO : OC : Read 3.5V voltage rail (ADC_3V5_MCU) - (mV) 3300 3542 3600 Pass 00:00.027
36 MCU LDO : OC : Measure the current over 4.6V high current rail (Vbus4V6H) (mA) 15 268 1000 Pass 00:00.022
37 BLE LDO : OC Pass 00:00.000
38 BLE LDO : OC : Release RST of 3.3V BLE LDO (LDO_BLE) Pass Pass 00:00.025
39 Delay 500ms Pass Pass 00:00.500
40 BLE LDO : OC : Read 3.3V BLE voltage rail (ADC_3V3_BLE) - (mV) 3250 3310 3350 Pass 00:00.035
41 BLE LDO : OC : Measure the current over 4.6V high current rail (Vbus4V6H) - (mA) 50 229 1000 Pass 00:00.036
42 LNA LDO : OC Pass 00:00.000
43 LNA LDO : OC : Release RST of 3.3V BLE LDO (LDO_LNA) Pass Pass 00:00.026
44 Delay 100ms Pass Pass 00:00.100
45 LNA LDO : OC : Read 3.3V BLE voltage rail (ADC_3V3_LNA) - (mV) 3250 3312 3350 Pass 00:00.034
46 LNA LDO : OC : Measure the current over 4.6V high current rail (Vbus4V6H) - (mA) 60 231 1000 Pass 00:00.026
47 Flashing NXP Pass 00:00.000
48 TesterMCU_BoardReset Pass Pass 00:00.029
49 Turn on the 4.6V high current source (Vbus4V6H) Pass Pass 00:00.024
50 Set SWD splitter to Out1 Pass Pass 00:00.022
51 Release NXP reset line Pass Pass 00:00.026
52 Jflash_Programming jlink2 workaround Pass Pass 00:02.021
53 Jflash_Programming jlink2 nxp boot Pass Pass 00:01.753
54 Jflash_Programming jlink2 nxp application Pass Pass 00:09.704
55 Set NXP reset line Pass Pass 00:00.026
56 Delay 500 Pass Pass 00:00.500
57 Release NXP reset line Pass Pass 00:00.026
58 Delay 500 Pass Pass 00:00.500
59 Flashing ISM Pass 00:00.000
60 Release all pinout Pass Pass 00:00.029
61 Delay 4000 Pass Pass 00:04.000
62 Set SWD splitter to Out2 Pass Pass 00:00.034
63 Jflash_Programming jlink2 TX boot Pass Pass 00:00.503
64 Jflash_Programming jlink2 TX application Pass Pass 00:00.940
65 Flashing BLE 1 Pass 00:00.000
66 Set SWD splitter to Out1 Pass Pass 00:00.025
67 Release RST of 3.3V BLE LDO (LDO_BLE) Pass Pass 00:00.027
68 Jflash_Programming jlink1 ble Pass Pass 00:01.269
69 Flashing BLE 2 Pass 00:00.000
70 Set SWD splitter to Out2 Pass Pass 00:00.037
71 Jflash_Programming jlink1 ble Pass Pass 00:01.233
72 Flashing BLE 3 Pass 00:00.000
73 Set SWD splitter to Out3 Pass Pass 00:00.031
74 Jflash_Programming jlink1 ble Pass Pass 00:01.227
75 Reader PWR reset Pass 00:00.000
76 Turn OFF the 4.6V high current source (Vbus4V6H) Pass Pass 00:00.028
77 Release NXP reset line Pass Pass 00:00.034
78 Release all pinout Pass Pass 00:00.036
79 Turn ON the 4.6V high current source (Vbus4V6H) Pass Pass 00:00.022
80 Delay 6000 Pass Pass 00:06.000
81 Reader Connect Pass 00:00.000
82 ConnectToReaderTelnet 192.168.0.187 Pass 00:00.343
83 ReaderSetSerialNumber 000005610 Pass 00:00.474
84 ReaderSetMacAddress 1063A390008C Pass 00:00.222
85 Restart Reader Pass Pass 00:00.104
86 Delay 6000 Pass Pass 00:06.000
87 ReConnectToReaderTelnet 192.168.0.187 Pass 00:00.340
88 ReaderGetMacAddress 1063A390008C Pass 00:00.216
89 SendReaderConfigFile Pass Pass 00:09.380
90 Get Main CPU version 2.1.1+1029 Pass 00:00.113
91 Get TX CPU version 0.15 Pass 00:00.719
92 Get BLE0 CPU version 0.10 Pass 00:00.114
93 Get BLE1 CPU version 0.10 Pass 00:00.102
94 Get BLE2 CPU version 0.10 Pass 00:00.105
95 Start TX (warming up) Pass 00:00.000
96 TesterMCU_Set_ISM_Mux Pass Pass 00:00.030
97 Set TX on pwr = 240 freq = 902000 debug Pass Pass 00:01.679
98 Delay 10000 Pass Pass 00:10.000
99 BLE RX CH 37 Pass 00:00.000
100 ReaderBLE_PreTestConfig Pass Pass 00:07.440
101 ReaderBLEtest ch 37 -43.22 Pass 00:08.088
102 ReaderBLEtest ch 37 ant 1 -50 -42.97 100 Pass 00:08.086
103 ReaderBLEtest ch 37 ant 2 -50 -44.92 100 Pass 00:08.084
104 ReaderBLEtest ch 37 ant 3 -50 -45.85 100 Pass 00:08.105
105 ReaderBLEtest ch 37 ant 4 -50 -42.00 100 Pass 00:08.088
106 ReaderBLEtest ch 37 ant 5 -50 -44.35 100 Pass 00:08.087
107 ReaderBLEtest ch 37 ant 6 -50 -43.25 100 Pass 00:06.012
108 ReaderBLEtest ch 37 ant 7 -50 -42.19 100 Pass 00:08.093
109 BLE RX CH 38 Pass 00:00.000
110 ReaderBLE_PreTestConfig Pass Pass 00:07.430
111 ReaderBLEtest ch 38 -50.99 Pass 00:12.224
112 ReaderBLEtest ch 38 ant 1 -50 -43.02 100 Pass 00:08.092
113 ReaderBLEtest ch 38 ant 2 -50 -43.03 100 Pass 00:08.099
114 ReaderBLEtest ch 38 ant 3 -50 -41.06 100 Pass 00:08.092
115 ReaderBLEtest ch 38 ant 4 -50 -39.00 100 Pass 00:08.081
116 ReaderBLEtest ch 38 ant 5 -50 -42.00 100 Pass 00:08.080
117 ReaderBLEtest ch 38 ant 6 -50 -41.06 100 Pass 00:08.089
118 ReaderBLEtest ch 38 ant 7 -50 -40.25 100 Pass 00:08.099
119 BLE RX CH 39 Pass 00:00.000
120 ReaderBLE_PreTestConfig Pass Pass 00:07.436
121 ReaderBLEtest ch 39 -41.02 Pass 00:08.066
122 ReaderBLEtest ch 39 ant 1 -50 -41.07 100 Pass 00:08.100
123 ReaderBLEtest ch 39 ant 2 -50 -45.25 100 Pass 00:08.085
124 ReaderBLEtest ch 39 ant 3 -50 -43.29 100 Pass 00:08.108
125 ReaderBLEtest ch 39 ant 4 -50 -40.99 100 Pass 00:06.020
126 ReaderBLEtest ch 39 ant 5 -50 -44.97 100 Pass 00:08.109
127 ReaderBLEtest ch 39 ant 6 -50 -45.89 100 Pass 00:05.993
128 ReaderBLEtest ch 39 ant 7 -50 -44.96 100 Pass 00:08.085
129 ReaderBLE_PreTestConfig - stop scan Pass Pass 00:07.430
130 TX Test Pass 00:00.000
131 SetSpectrum Pass Pass 00:00.002
132 Get Last Spectrum Mesurment Freq 901973097.62 Pass 00:00.513
133 Get Last Spectrum Mesurment Amp 20 29.03 100 Pass 00:00.000
134 TX Calibration Pass 00:00.000
135 Reader Tx Warmup target 40 C - 45 C 38 69.75 45 Fail 10:00.779
136 ReaderCTune ( target freq - measure freq) (Hz) 0 temp=69.75 400 Error 00:01.117
137 C -Tune Selected Xi Xo -1,-1 Pass 00:00.000
138 Reader TX Calibration Low 865700000Hz High 915000000Hz Done Pass 01:47.868
139 ReaderTxStoreCalibrationData Missing TX calibration data Error 00:00.012
140 TX Test - post calibration Pass 00:00.000
141 Restart Reader Pass Pass 00:00.100
142 Delay 6000 Pass Pass 00:06.000
143 ReConnectToReaderTelnet 192.168.0.187 Pass 00:00.329
144 SendReaderConfigFile Pass Pass 00:09.611
145 SetSpectrum Pass Pass 00:00.000
146 Set TX on 30 928000 open Pass Pass 00:01.683
147 Get Last Spectrum Mesurment Freq 928996000 927972149.35 928004000 Pass 00:00.489
148 Get Last Spectrum Mesurment Amp 28 26.77 32 Fail 00:00.000
149 SetSpectrum Pass Pass 00:00.000
150 Set TX on 25 865700 open Pass Pass 00:01.684
151 Get Last Spectrum Mesurment Freq 865796000 865333238.94 865704000 Pass 00:00.485
152 Get Last Spectrum Mesurment Amp 23 -29.54 27 Fail 00:00.000
153 SetSpectrum Pass Pass 00:00.000
154 Set TX on 30 865700 open Unable to write data to the transport connection: An existing connection was forcibly closed by the remote host.. Error 00:00.000
155 Get Last Spectrum Mesurment Freq 865796000 865333238.94 865704000 Pass 00:00.509
156 Get Last Spectrum Mesurment Amp 28 -30.97 32 Fail 00:00.000
157 Set TX off A connection attempt failed because the connected party did not properly respond after a period of time, or established connection failed because connected host has failed to respond. [::ffff:192.168.0.187]:23 Error 00:21.034
158 Finalize Pass 00:00.000
159 Finalize Pass Pass 00:00.069
Back to List