GuiSession

stationCode
ReaderFT_01
scandData
RevC Test,RevC Test
ATPName
Reader2.0_FullATP_20241110_112301
startTime
11/11/2024 09:06:16
endTime
11/11/2024 09:08:16
Duration
02:00.194
Status
Error

Test Results

index TestName Min Limit ResultAnswer Max Limit ResultStatus Duration
0 Initialize Pass 00:00.000
1 init Pass Pass 00:03.753
2 PoE : OC Pass 00:00.000
3 PoE : OC : Open circuit test :Turn on the 54V Pass Pass 00:00.185
4 PoE : OC : Set NXP RST Pass Pass 00:00.037
5 Delay 1000ms Pass Pass 00:01.000
6 PoE : OC : Read PoE+ voltage rail (PoE_P_ADC) (mv) 0 Pass 00:00.159
7 PoE : OC : PoE VDD voltage rail (PoE_VDD_ADC) (mv) 1 Pass 00:00.157
8 PoE : OC : PoE VDD voltage rail (PoE_VT15_ADC) (mv) 0 Pass 00:00.158
9 PoE : OC : Measure the current over 54V rail (Vbus54V) (mA) 30 Pass 00:00.036
10 PoE : OC : Read 4.6V rail voltage (ADC_4V6_Load) (mv) 4450 4533 4650 Pass 00:00.028
11 PoE : CC Pass 00:00.000
12 PoE : CC : turn on Load 4.6V rail with external resistor (Load4V6) Pass Pass 00:00.027
13 Delay 100ms Pass Pass 00:00.100
14 PoE : CC : Read PoE+ voltage rail (PoE_P_ADC) (mv) Skip Pass 00:00.000
15 PoE : CC : PoE VDD voltage rail (PoE_VDD_ADC) (mv) Skip Pass 00:00.000
16 PoE : CC : PoE VDD voltage rail (PoE_VT15_ADC) (mv) Skip Pass 00:00.000
17 PoE : CC : Measure the current over 54V rail (Vbus54V) (mA) 229 Pass 00:00.025
18 PoE : CC : Read 4.6V rail voltage (ADC_4V6_Load) (mv) 4295 Pass 00:00.026
19 PoE : CC : turn off Load 4.6V rail with external resistor (Load4V6) Pass Pass 00:00.034
20 PoE : CC : Open circuit test :Turn Off the 54V Pass Pass 00:00.036
21 PA 4.6V : OC Pass 00:00.000
22 PA 4.6V : OC : Turn on the 4.6V high current source (Vbus4V6H) Pass Pass 00:00.028
23 Delay 500ms Pass Pass 00:00.500
24 PA 4.6V : OC : Read 4.6V PA voltage rail 4100 4504 4600 Pass 00:00.034
25 PA 4.6V : OC : Measure the current over 4.6V high current rail 50 177 600 Pass 00:00.021
26 PA 4.6V : CC : Pass 00:00.000
27 PA 4.6V : CC : Load 4.6V PA rail with external resistor Skip Pass 00:00.000
28 Delay 100ms Skip Pass 00:00.000
29 PA 4.6V : CC : Read 4.6V PA voltage rail 2400 Skip 2800 Pass 00:00.000
30 PA 4.6V : CC : Measure the current over 4.6V high current rail 1000 Skip 2000 Pass 00:00.000
31 PA 4.6V : CC : Turn off the external load for 4.6V PA rail Skip Pass 00:00.000
32 MCU LDO : OC Pass 00:00.000
33 MCU LDO : OC : Release NXP RST Pass Pass 00:00.033
34 Delay 500ms Pass Pass 00:00.500
35 MCU LDO : OC : Read 3.5V voltage rail (ADC_3V5_MCU) - (mV) 3300 3539 3600 Pass 00:00.040
36 MCU LDO : OC : Measure the current over 4.6V high current rail (Vbus4V6H) (mA) 15 283 1000 Pass 00:00.032
37 BLE LDO : OC Pass 00:00.000
38 BLE LDO : OC : Release RST of 3.3V BLE LDO (LDO_BLE) Pass Pass 00:00.033
39 Delay 500ms Pass Pass 00:00.500
40 BLE LDO : OC : Read 3.3V BLE voltage rail (ADC_3V3_BLE) - (mV) 3250 3312 3350 Pass 00:00.042
41 BLE LDO : OC : Measure the current over 4.6V high current rail (Vbus4V6H) - (mA) 50 246 1000 Pass 00:00.035
42 LNA LDO : OC Pass 00:00.000
43 LNA LDO : OC : Release RST of 3.3V BLE LDO (LDO_LNA) Pass Pass 00:00.029
44 Delay 100ms Pass Pass 00:00.100
45 LNA LDO : OC : Read 3.3V BLE voltage rail (ADC_3V3_LNA) - (mV) 3250 3317 3350 Pass 00:00.026
46 LNA LDO : OC : Measure the current over 4.6V high current rail (Vbus4V6H) - (mA) 60 249 1000 Pass 00:00.036
47 Flashing NXP Pass 00:00.000
48 TesterMCU_BoardReset Pass Pass 00:00.036
49 Turn on the 4.6V high current source (Vbus4V6H) Pass Pass 00:00.024
50 Set SWD splitter to Out1 Pass Pass 00:00.034
51 Release NXP reset line Pass Pass 00:00.027
52 Jflash_Programming jlink2 workaround Pass Pass 00:02.011
53 Jflash_Programming jlink2 nxp boot Pass Pass 00:01.737
54 Jflash_Programming jlink2 nxp application Pass Pass 00:09.899
55 Set NXP reset line Pass Pass 00:00.032
56 Delay 500 Pass Pass 00:00.500
57 Release NXP reset line Pass Pass 00:00.025
58 Delay 500 Pass Pass 00:00.500
59 Flashing ISM Pass 00:00.000
60 Release all pinout Pass Pass 00:00.030
61 Delay 4000 Pass Pass 00:04.000
62 Set SWD splitter to Out2 Pass Pass 00:00.025
63 Jflash_Programming jlink2 TX boot Pass Pass 00:00.499
64 Jflash_Programming jlink2 TX application Pass Pass 00:00.936
65 Flashing BLE 1 Pass 00:00.000
66 Set SWD splitter to Out1 Pass Pass 00:00.035
67 Release RST of 3.3V BLE LDO (LDO_BLE) Pass Pass 00:00.033
68 Jflash_Programming jlink1 ble Pass Pass 00:01.213
69 Flashing BLE 2 Pass 00:00.000
70 Set SWD splitter to Out2 Pass Pass 00:00.031
71 Jflash_Programming jlink1 ble Pass Pass 00:01.211
72 Flashing BLE 3 Pass 00:00.000
73 Set SWD splitter to Out3 Pass Pass 00:00.032
74 Jflash_Programming jlink1 ble Pass Pass 00:01.199
75 Reader PWR reset Pass 00:00.000
76 Turn OFF the 4.6V high current source (Vbus4V6H) Pass Pass 00:00.035
77 Release NXP reset line Pass Pass 00:00.029
78 Release all pinout Pass Pass 00:00.027
79 Turn ON the 4.6V high current source (Vbus4V6H) Pass Pass 00:00.022
80 Delay 6000 Pass Pass 00:06.000
81 Reader Connect Pass 00:00.000
82 ConnectToReaderTelnet 192.168.0.150 Pass 00:00.317
83 ReaderSetSerialNumber Error - SN not found Error 00:00.000
84 ReaderSetMacAddress Error - SN not found Error 00:00.110
85 Restart Reader Pass Pass 00:00.104
86 Delay 6000 Pass Pass 00:06.000
87 ReConnectToReaderTelnet 192.168.0.150 Pass 00:00.304
88 ReaderGetMacAddress Error - SN not found Error 00:00.111
89 SendReaderConfigFile Pass Pass 00:08.900
90 Get Main CPU version 2.1.1+1029 Pass 00:00.112
91 Get TX CPU version 0.15 Pass 00:00.728
92 Get BLE0 CPU version 0.10 Pass 00:00.109
93 Get BLE1 CPU version 0.10 Pass 00:00.723
94 Get BLE2 CPU version 0.10 Pass 00:00.729
95 Start TX (warming up) Pass 00:00.000
96 TesterMCU_Set_ISM_Mux Pass Pass 00:00.024
97 Set TX on pwr = 240 freq = 902000 debug Pass Pass 00:01.697
98 Delay 10000 Pass Pass 00:10.000
99 BLE RX CH 37 Pass 00:00.000
100 ReaderBLE_PreTestConfig Unable to write data to the transport connection: An existing connection was forcibly closed by the remote host.. Error 00:00.032
101 ReaderBLEtest ch 37 Unable to write data to the transport connection: An existing connection was forcibly closed by the remote host.. Error 00:01.513
102 ReaderBLEtest ch 37 ant 1 -50 A connection attempt failed because the connected party did not properly respond after a period of time, or established connection failed because connected host has failed to respond. [::ffff:192.168.0.150]:23 100 Error 00:21.061
103 ReaderBLEtest ch 37 ant 2 -50 Unable to write data to the transport connection: An existing connection was forcibly closed by the remote host.. 100 Error 00:01.515
104 ReaderBLEtest ch 37 ant 3 -50 A connection attempt failed because the connected party did not properly respond after a period of time, or established connection failed because connected host has failed to respond. [::ffff:192.168.0.150]:23 100 Error 00:21.041
Back to List